5T-20T Laboratory Manual Hydraulic Rubber Vulcanizing Press Machine

5T-20T Laboratory Manual Hydraulic Rubber Vulcanizing Press Machine   Introduction The 6014H series manual hydraulic flat vulcanizing press is a major equipment used for pressing and forming various rubber model products and non-model products. It can also be used for pressing various thermosetting plastics and foamed rubber and plastic products. It has an independent power mechanism and electrical system, which are centrally controlled by buttons. The working pressure and heating temperature can both be adjusted within a certain range   Technical parameter Model 6014H-5 6014H-10 6014H-20 Pressure capacity 5T 10T 20T Pressure gauge The hydraulic gauge is manually controlled for pressure Pressure plate size (mm metric) 250*250/300*300/350*350/400*400/450*450/500*500 mm Material of hot press plate High-temperature resistant imported steel plate, surface carbonized and quenched, special treatment for fast heat conduction, no deformation under parallel pressure, wear-resistant Hardness of the pressure plate 50~60HRC Flatness of the pressure plate ≤ 0.03 mm Flatness of the pressure plate ≤ 0.16 mm Temperature range Room temperature -250℃ [Customizable maximum temperature: 500 ℃] Temperature uniformity 1.5℃ [The larger the pressure plate, the higher the temperature and the worse the temperature uniformity.] Temperature controller Two Omron temperature controllers Temperature control method PID self-tuning in combination with high-precision sensors ensures temperature control accuracy of ±1.0℃. Timer The LED time range is 0.1s - 99 minutes - 9.9 hours Heater The heating mold is built-in cylindrical Heating time It takes approximately 15 minutes from room temperature to 160℃ Two hot plates The temperature of the hot plate can be set separately Heating method Electric heating Cooling method Natural cooling Cylinder stroke Max 100mm [customizable Cylinder speed 5mm/s [Manual] Pressure gauge 0~200kg/sq.cm Mold opening method Manual ascent and descent Host volume (mm) 400x550x600 500x550x600 550x550x600 Power supply voltage 3 phase, AC220V 3 phase, AC220V 3 phase, AC220V Overall weight of the machine About 150kg About 270kg About 350kg    

200T Semi-Automatic Double-Layer Hydraulic Rubber Vulcanizing Press Machine

200T Semi-Automatic Double-Layer Hydraulic Rubber Vulcanizing Press Machine   Introduction The semi-automatic double-layer vulcanizing machine adopts imported hydraulic components and electrical components. Under the action of the working fluid pressure, the plunger of the vulcanizing machine rises and descends (i.e., the hot plate opens). Relying on the self-weight of the hot plate, the platform and the plunger, the working fluid flows back to the oil storage tank, achieving the purpose of descending (i.e., opening). The working fluid of the vulcanizing machine enters the cylinder through the control valve. By turning the control handle to different positions, the plunger of the flat vulcanizing machine can rise or fall. Features This series of models is equipped with automatic control devices for pressure, time and temperature. It can achieve mold closing and pressure increase, timed working cycles, and automatic pressure replenishment to ensure the quality of pressed products. The structure is compact, the appearance is beautiful, and the operation is convenient. This product is a new generation of flat vulcanizing machine. It adopts a working mode where a fast cylinder drives the plunger to automatically draw in oil. Compared with the previous flat vulcanizing machines driven by high and low pressure oil pumps, it saves energy by more than 30%. And significantly enhance work efficiency. It is the preferred product for energy conservation and environmental protection. It adopts a 7.1-inch large touch screen for operation and can preset 6 sets of mold vulcanization parameters. It is equipped with a parameter password protection function, and workers cannot change the equipment parameters at will It has an automatic locking function during vulcanization. In the vulcanization state, workers cannot open the mold at will unless a password is entered to unlock it, ensuring the vulcanization time of the product. It has the function of output memory. It can store and remember the output within a week, making the production capacity clear at a glance. It has a timed heating function and can be set to start heating at any time within 24 hours of a day. Application This product is widely used in the following industries: The semi-automatic double-layer vulcanizing machine series hydraulic press is suitable for the rolling, embossing, forming of thin metal sheets and the shallow drawing process of plastic materials. Such as the pressing of watch cases, case backs, watch straps, various gold and silver jewelry, badges, commemorative coins, glasses, and the shells of lighting fixtures, etc. The main equipment used for pressing various rubber model products and non-model products can also be used for pressing various thermosetting plastics and foamed rubber and plastic products. Technical parameters Nominal force (T) 200 Rated working pressure (MPa) 25 Spacing (mm) 150 Stroke (mm) 300 Number of oil cylinders Main cylinder1, Auxiliary cylinder2 Inner diameter of the oil cylinder (mm) 320 Number of working levels 2 Number of heating plates 3 Heating method electric Heating power (KW) 14.4 Control mode automatic Effective area of the heating plate (mm) Left & right 600 Front & back 600