100L Vacuum Planetary Mixer: Tailored for Battery R&D Labs & High-Viscosity Industrial Production Lines

100L Vacuum Planetary Mixer: Tailored for Battery R&D Labs & High-Viscosity Industrial Production Lines Ⅰ. Equipment Features: Application Scope After the slurry is prepared by the mixer, the bucket is moved to the lifting machine, covered with a mixing head to form a transfer tank. This setup completes slurry transfer from the mixing area to storage or coating area. The slurry is delivered to the main storage tank or coater via quick-connect adapters.   Ⅱ. Main Technical Parameters: Container Parameters l Design Total Volume: 140 L l Effective Volume: 45–100 L l Inner Diameter: 596 mm l Inner Depth: 500 mm l Material (contacting with medium): SS304 l Jacket Type: Single-layer on side and bottom, for heating or cooling l Jacket Connection: G3/4″ quick coupling, pressure ≤0.4 MPa l Jacket Circulation: Customer-supplied; inlet ≤8 °C, flow >40 L/min l Discharge: One G1-1/2″ three-piece ball valve at bottom with 2″ ISO quick coupling l Ambient Temperature: –10 °C to +120 °C l Movement: On casters l Interchangeable with 100 L mixer bucket   Mixing Components l Frequency: 50 Hz l Mixing Motor Power: 1.1 kW (1 unit) l Mixing Speed: 42 rpm (fixed) l Impeller Diameter: 576 mm l Impeller Type: Inclined paddle screw strip l Material: SS304 l Tip Speed: 1.2 m/s l Number of Impellers: 1 l Number of Shafts: 1 l Clearance (impeller to wall): 10 mm l Clearance (impeller to bottom): 8 mm l Principle: Prevents sedimentation with unique impeller design   Top Cover Components l Material: SS304 l Feed Port: ISO standard quick coupling 1″ ×1 l Sight Glasses: DN80 tempered glass ×2 l Vacuum Port: G3/4″ ×1 set (vacuum/vent) l Digital Vacuum Gauge Port: M14×1.5 internal thread ×1   l Control System l Cabinet: Houses inverter and low-voltage components l Manual Panel: Buttons, knobs, instruments l Power: AC 3×380 V ±5%, 50 Hz l Control: Electrical l Operation: Cabinet panel with buttons/knobs l Emergency Stop: 1 l Start Button: 1 l Stop Button: 1 l Work Light Switch: 1   Safety Interlock System Emergency Stop: Immediately halts the system; prevents any further operation   Other Notes l Seals: Domestic brand; static by O-ring, dynamic by mechanical or skeleton seal l Grease: Domestic l Valves: Domestic l Vacuum Requirement: Customer to supply vacuum system, 8 L/s (2X-8) l Vacuum Retention: –0.098 MPa; holds >–0.085 MPa for 24 h without leakage l Main Power: >1 kW l Weight: Approx. 250 kg l Dimensions: L830 mm × W830 mm × H1474.5 mm l Color: Ivory white l Floor Load: 400 kg/m²   Ⅲ. List of Standard Wear Parts: No. Name Specification Material Quantity Remarks 1 Top Lid Seal Ring ΦD×ΦN Silicone 1 Matched to model, per supplier standard 2 Sight Glass Seal Ring — Silicone 2 Matched to model, per supplier standard 3 Feed Port Gasket — Silicone 1 Matched to model, per supplier standard 4 Sight Glass Pane Tempered Glass 2 pcs Matched to model, per supplier standard   Ⅳ. Supporting Conditions: No. Item Standard Requirement 5 Workshop Height >3.0 m; ensure lift space and maintenance clearance; floor must be clean, level 6 Door Dimensions Height >2.0 m; Width >1.5 m; ensure equipment can pass through 7 Cooling Water Must meet cooling demand; forced cooling preferred; heating in winter optional 8 Heating Maintain >20 °C in winter to avoid hydraulic oil solidifying; ensure lubrication 9 Installation Space Follow layout drawing 10 Air Supply 5–7 kgf/cm², 50 L/min; for pneumatic pump and other uses 11 Other No corrosive/explosive gases or liquids